Lab 33: Configuring and Naming Static Routes

root

Leader IT/Architect
Dec 31, 2012
1,153
72
48
Lab 33: Configuring and Naming Static Routes
Lab Objective:
The objective of this lab exercise is to configure named static routes via next hop IP addresses on interfaces connected to a switch on two routers. This lab also goes through the validation of the configured static routes.
Lab Purpose:
Static route configuration is a fundamental skill. There are several methods to configure static routes on a Cisco router, and each way has its pros and cons. Naming the static routes allows you to easily identify what each static route is used for as you view the router configuration. As a Cisco engineer, as well as in the Cisco CCNA exam, you will be expected to know how to configure named static routes via any of the methods available in Cisco IOS.
Certification Level:
This lab is suitable for both CCENT and CCNA certification exam preparation
Lab Difficulty:
This lab has a difficulty rating of 5/10
Readiness Assessment:
When you are ready for your certification exam, you should complete this lab in no more than 15 minutes
Lab Topology:
Please use the following topology to complete this lab exercise:
101labs_fig30.png

Task 1:
Configure the hostnames on routers R1 and R2, as well as Sw1 as illustrated in the topology.
Task 2:
Configure Sw2 as a VTP sever and configure VLAN 10 named STATIC. Assign ports FastEthernet0/1 and FastEthernet0/2 to this VLAN. Configure the DCE interface Serial0/0 in R1 to provide clocking to R2 at a clock speed of 768Kbps.
Task 3:
Configure IP addresses 172.27.32.1/30 and 172.27.32.2/30 on R1 and R2 Fa0/0 interfaces respectively. Configure IP addresses 192.168.7.1/30 and 192.168.7.2/30 on R1 and R2 S0/0 interfaces respectively. In addition to that configure the Loopback interfaces on R1 with the IP addresses in the topology.
Task 4:
Configure a static route named LAN-ROUTE on R2 via interface FastEthernet0/0 with a next hop IP address of 172.27.32.1 to the 10.88.100.0/27 subnet. Configure a static route named WAN-ROUTE on R2 via Serial0/0 with a next hop IP address of 192.168.7.1 to the 10.99.100.0/27 subnet. Verify your static route configuration.
Task 5:
Ping each Loopback interface configured on R1 from R2 to verify your static route configuration.

Nguồn:
http://www.howtonetwork.net/public/1413.cfm
 
Task 1:
Configure the hostnames on routers R1 and R2, as well as Sw1 as illustrated in the topology
Router#configure terminal
Router#hostname R1
Router#configure terminal
Router#hostname R2
Switch#configure terminal
Switch#hostname Sw1


Task 2:
Configure Sw2 as a VTP sever and configure VLAN 10 named STATIC. Assign ports FastEthernet0/1 and FastEthernet0/2 to this VLAN. Configure the DCE interface Serial0/0 in R1 to provide clocking to R2 at a clock speed of 768Kbps.

  • Configure Sw2 as a VTP sever and configure VLAN 10 named STATIC. Assign ports FastEthernet0/1 and FastEthernet0/2 to this VLAN.
Switch(config)#interface f0/1
Switch(config-if)#switchport mode access
Switch(config-if)#switchport access vlan 10
Switch(config)#interface f0/2
Switch(config-if)#switchport mode access
Switch(config-if)#switchport access vlan 10


  • Configure the DCE interface Serial0/0 in R1 to provide clocking to R2 at a clock speed of 768Kbps. 768 = 768 000bps
R1#sh controllers s0/0/0
R1#configure terminal
R1(config)#interface s0/0/0
R1(config-if)#clock rate 800000
2014-02-01_152432.jpg

Task 3:

Configure IP addresses 172.27.32.1/30 and 172.27.32.2/30 on R1 and R2 Fa0/0 interfaces respectively. Configure IP addresses 192.168.7.1/30 and 192.168.7.2/30 on R1 and R2 S0/0 interfaces respectively. In addition to that configure the Loopback interfaces on R1 with the IP addresses in the topology.
R1(config)#interface f0/0
R1(config-if)#ip address 172.27.32.1 255.255.255.252
R1(config-if)#no shutdown

R1(config)#interface s0/0/0
R1(config-if)#ip address 192.168.7.1 255.255.255.252
R1(config-if)#no shutdown

R1(config-if)#interface lo100
R1(config-if)#ip address 10.88.100.1 255.255.255.224
R1(config-if)#interface lo101
R1(config-if)#ip address 10.99.100.1 255.255.255.224
R2(config)#interface f0/0
R2(config-if)#ip address 172.27.32.2 255.255.255.224
R2(config-if)#no shutdown


Task 4:
Configure a static route named LAN-ROUTE on R2 via interface FastEthernet0/0 with a next hop IP address of 172.27.32.1 to the 10.88.100.0/27 subnet. Configure a static route named WAN-ROUTE on R2 via Serial0/0 with a next hop IP address of 192.168.7.1 to the 10.99.100.0/27 subnet. Verify your static route configuration.
R2(config)#ip route 10.88.100.0 255.255.255.224 172.27.32.1 name LAN-ROUTE
R2(config)#ip route 10.99.100.0 255.255.255.224 192.168.7.1 name WAN-ROUTE

Task 5:
Ping each Loopback interface configured on R1 from R2 to verify your static route configuration.
2014-02-05_151332.jpg

* Lưu ý:
  • Việc cấu hình tên của static route thì không được hiện trong bảng định tuyến (#sh ip route : sẽ không hiện tên)
  • Tên này chỉ hiện trong running-config
R2#sh running-config | include route
2014-02-05_151741.jpg
 
hi bạn,

Đã upload lại hình ảnh cho bài lab rồi nhé!

Thanks,
 

About us

  • Securityzone.vn là một trang web chuyên về an ninh mạng và công nghệ thông tin. Trang web này cung cấp các bài viết, tin tức, video, diễn đàn và các dịch vụ liên quan đến lĩnh vực này. Securityzone.vn là một trong những cộng đồng IT lớn và uy tín tại Việt Nam, thu hút nhiều người quan tâm và tham gia. Securityzone.vn cũng là nơi để các chuyên gia, nhà nghiên cứu, sinh viên và người yêu thích an ninh mạng có thể trao đổi, học hỏi và chia sẻ kiến thức, kinh nghiệm và giải pháp về các vấn đề bảo mật trong thời đại số.

Quick Navigation

User Menu